[제품설명]
* 산업용, 상업용 설치에 적합
* Low 인피던스 High 인피던스 겸용
* 1 INPUT, 1 OUTPUT 80W (4옴), 80W (70V/100V) * Single - zone
* Optional Accessories 1-VCAP remote volume control for one channel. 4-VCAP remote volume control for four channels. |
[제품스펙]
The 280A shall have the following specifi cations:
Minimum guaranteed power into 4 ohms or 70V/100V output: 80W maximum
power at 1 kHz with 0.5% THD. Frequency Reponse (at 1 watt from
4-ohm tap): 70 Hz - 19 kHz +/– 1 dB. Frequency Response (at line out): 20
Hz to 20 kHz +/–1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maxium
1 kHz power): 50 Hz to 20 kHz with < 0.5% THD. Signal to Noise Ratio (ref.
to rated power, master volume at minimum): 85 dB. DC Output Offset:
< ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity
(for full output at maximum gain): 800 mV. Input Impedance (nominal):
100 kilohms. Minimum Load Impedance: 100V output 160 ohms, 70V
output 80 ohms, 4-ohm output 4/8 ohms. Crosstalk: –70dB at 1kHz. Line
Output Level (nominal): 1V into 10 kilohms. AC Line Voltages Available:
100V 50/60 Hz, 120V 60 Hz, 220V 50/60 Hz, 230V 50/60 Hz, 240V
50/60 Hz. Operating Temperature/Humidity: 0 degrees C to 40 degrees
C at 95% relative humidity (non-condensing). Storage Temperature: –20
degrees C to 85 degrees C.
Front Panel Controls and Indicators
Front panel controls and indicators shall include the following:
Power Switch: Pushbutton on-off switch. Master Volume Controls: One per
output channel, detented potentiometer with knob. Tone Controls: Bass and
Treble non-detented potentiometers on each channel, Bass ±10 dB at 100
Hz, Treble ±10 dB at 10 kHz. Power Indicator: Blue LED indicates power on.
Output Signal Presence Indicator: Green LED, one for each input channel,
illuminates when input signal exceeds 100 mV (45 dB below full power)
from the 4-ohm tap. Clip Indicators: Red LED, one per output channel,
illuminates at threshold of audible distortion.
Rear Panel Controls and Connectors
Rear panel controls and connectors shall include the following:
Reset Button: Resets the circuit breaker that protects the power supply;
220/230/240V units shall have a fuse instead. AC Power Inlet: Detachable
IEC. Auxiliary Power Input: 2-position terminal strip for 24 VDC
(±10%) backup power; accepts up to 14 AWG terminal forks. Amplifi er
Outputs Connectors: One per channel, 4-position terminal strip with COM
(Common), 4 ohms, 70V and 100V terminals; accepts up to 10 AWG
terminal forks, non-touch cover included. Output VCA Connector: 4-pin
Phoenix-type connector for two VCA control lines of +10 VDC and ground;
compatible with Crown 1-VCAP and 4-VCAP modules. Line Out Connector:
One 3-pin balanced Phoenix-type connector per output channel, post
master, pre-VCA, level controlled by master volume control. Amp Input
Connector: 3-pin Phoenix-type, high-impedance balanced, one per amplifi
Cooling shall be by convection. Included protection mechanisms shall
be current limiting, over-temperature thermal cutout, and DC-fault load
Included accessories shall be a power cord, detachable rack ears, screws
for rack ears, non-touch cover for output connectors, Phoenix-type connectors,
and spade lugs. Optional accessories shall be a 1-VCAP remote
volume control for one channel, and a 4-VCAP remote volume control for
The dimensions of the amplifi er shall allow for 19 inch (48.3 cm) EIA
standard (RS-310-B) rack mounting. The amplifi er shall be 3.5 inches (8.9
cm) high, and 12.2 inches (31 cm) deep behind the rack-mounting surface
(not including the non-touch cover).
The amplifi er shall weigh 25.3 lb (11.5 kg).
The amplifi er shall be designated the Crown 280A. | | |
|