[제품 스팩]
INPUT
Type: Active balanced
Impedance: 20k Ohms balanced, 10k Ohms unbalanced
Max Level: +23dBu
OUTPUT
Type: Servo-balanced
Min Load: 200 Ohms balanced, 100 Ohms unbalanced
Max Level: +23dBu
I/O CONNECTORS
XLR, 1/4"TRS, Eurobock
FREQUENCY RESPONSE
+/-.25dB 2-Hz-20kHz
IM DISTORTION (SMPTE)
<.01% @+20dBu
TOTAL HARMONIC DISTORTION
<.01% @+20dBu, 20Hz-20kHz
OUTPUT NOISE
<-92dBu unweighted
CROSSTALK
<-90dB MQX2150 (20Hz-20kHz)
FILTERS
MQX2150
Type: Constant Q Wein-Bridge
Number: 2x15
Bandwidth: 2/3 Octave
Tolerance: +/-3%
Range: +/-15dB
Subsonic: 18dB/Octave @20Hz (internally switchable)
MQX2310
Type: Constant Q Wein-Bridge
Number: 2x31
Bandwidth: 1/3 Octave
Tolerance: +/-3%
Range: +/-15dB
Subsonic: 18dB/Octave @40Hz
POWER REQUIREMENTS
100-240VAC, 50-60Hz, 24W
SHIPPING WEIGHT
MQX2150: 14lb.
MQX2310: 16lb.
DIMENSIONS
MQX2150: 19"W x 1.75"H x 8"D
MQX2310: 19"W x 3.5"H x 8"D
[제품 설명]
MQX Series Graphic Equalizer는 GQX Series와 같은 성능과 디자인의 제품을 Compact 사이즈로 만들어 장비의 이동
을 보다 용이하게 만든 제품이다.
• 스테레오 15밴드 그래픽 이퀄라이저
MQX-2150
The graphic equalizer shall be stereo (2 channels). Each channel shall consist of 15 bands centered on standard
ISO frequencies at intervals of 2/3 octave and covering a frequency range of 25Hz to 16kHz. Individual bands
shall be activated by linear slide faders with a 25mm travel, and a tactile center detent. The range of equalization
per band shall be switchable between ±15dB or ±6dB.
The equalizer shall have a gain of unity with all sliders centered, and shall have a maximum in/out level of
+23dBu. Frequency response shall be ±.25dB 20Hz to 20kHz. Hum and noise shall be at least -96dBu and
SMPTE intermodulation distortion or THD shall be less than 0.01% at +20dBu. Input impedance shall be 20k ohm
balanced, 10k ohm unbalanced. Output impedance shall be 200 ohm balanced, 100 ohm unbalanced.
Inputs and outputs shall be balanced type on both XLR, 1/4" and Euroblock. Individual filters shall be Wein-bridge
type and connected in a summing circuit optimized for minimum filter interaction and constant bandwidth at any
slider setting. Boost and cut characteristics shall be fully symmetrical, with the filter being electrically removed
from the circuit in the center (flat) position. Individual filters shall be accurate to within 3% of indicated center
frequency and shall be non-adjustable to insure long term accuracy.
The equalizer shall also include an 18dB per octave high pass filter at 20Hz, internally selectable. A green signal
presence and red clip indicators shall show critical operating levels. Input gain shall be adjustable over minus
infinity to +6dB, and an overall EQ bypass switch shall be included. The equalizer shall weigh 6.5 lbs net and
mount in a standard 19. rack using 1 space (1.75. high). The power requirement shall be 100- 240VAC, 50-60Hz,
24W. The unit shall be an Ashly Audio MQX-2150.